Creating a Layout, Section and Elevation with dimensions using AutoCad
AIM: DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE. DETAILS OF PROJECT: THE GIVEN PLAN CONSIST OF A FLOOR PLAN OF A BUILDING ,SECTION,AND ELEVATION DETAILS AND THE STEP BY STEP PROCESS IS GIVEN BELOW. PLAN CONSIST OF 3 FLOORS AND THE SECTION OF THE PLAN ARE GIVEN WITH DETAILS…
Sandeep Sathi
updated on 17 Dec 2021
AIM:
DRAWING THE GIVEN PLAN USING AUTOCAD SOFTWARE.
DETAILS OF PROJECT:
THE GIVEN PLAN CONSIST OF A FLOOR PLAN OF A BUILDING ,SECTION,AND ELEVATION DETAILS AND THE STEP BY STEP PROCESS IS GIVEN BELOW.
PLAN CONSIST OF 3 FLOORS AND THE SECTION OF THE PLAN ARE GIVEN WITH DETAILS OF STRE CASE ETC
PROCDURE:
STEP:1
For the given drawings the units are set according to the requirements.
The limits of the page are set to 1000,1000 in x y directions respectively.
Dimention style commond is used to set the height of the text,arrow size an the primary units.units are set to engineering.
STEP:2
Line commont(direct line system ) is used more frequently to draw the given lines as per the dimentions.
Tream option is used to tream the excess patrt of the figures some times erase.
Dim tool is used to determine the dimentions of the lnes that are to be mentioned.
HATCH tol is used to fill the patterns.
Mtext is used to write the text on the sheet to specify the details of the drawings.
Fillet is used to fill the corners where there are not joined corectely or disconnected.
Chamfer used to fill the corners with curved edges where they are to be joined with curved part.
F8 option is used for ortho,F9 is for snap
STEP:3
Following are the some of the most frequently used commonds and tools
FILLET,HATCH,DIMENTIONS,MTEXT,PEDIT,LEADERS,COPY,MOVE ETC.
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Be the first to add a comment
Read more Projects by Sandeep Sathi (29)
Calculation of Stiffness in Structural elements
1st question: find the stiffness co efficient of the system. In the given figure there are three degree of freedoms as fiven 2 are rotational and one is translate motion. Lets consider the unit displacement. Given conditions L=2h EI of beam=EI of column For the displacement u1 1)K for the column in translation=2x …
09 Jul 2022 05:35 AM IST
Identification of Cracks
FAILURES AT JOINTS: In general the failures occur due to low stability,strength and inadequate durability. 1ST QUESTION Fig:a In the figure the failure occur at the edge of the beam and the failure occur only for the beam this typwe of failure occur due to moment in the beams in the opposite direction. It will not repaced…
12 Apr 2022 02:00 PM IST
Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork
1ST ANS:EXPORTING THE REVIT MODEL. After the completion of the structural analysis of the model using structural analysis next the model is exported to Navisworks for the view and schedule purpose. For exporting the model from revit to naviswork we need to install naviswork export with the appropriate version. After the…
13 Mar 2022 02:06 PM IST
Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo
1ST ANS:SIN CURVE CREATION: Step:1 For the creation f an sin curve first we have to create a set of points. For he creation of the points range option is taken and then for the for the values of start,end,phase code block is used to assain te values for the curve or we can use slider to assin the values. Step:2 After the…
11 Mar 2022 01:12 PM IST
Related Courses
